here’s some more because the jersey meet pics got too thuggish.
wow. Kyle, you seriously need to give a refund minus the material costs (which i think you said it was like $50). the cross bars are not even lining up on the center of the bar.
PRECISELY… everyone look at the pictures mark posted for me. the one that went up today should be studied closely for this lack of straightness. everywhere. the very last pic shows it best. its not a very easy thing to take a picture of, especially with my camera. but once again, even then you can still tell its off by quite a bit. there is one more picture that needs to go up… (mark the X2 one… could u get that up) and ill post the measurements i took of the bar. basically there isnt one consistent measurement or angle on any part of the bar, anywhere. this is proof KYLE that I DID NOT receive what i paid for. its completely crooked. more to come… :bang:
oglesport is awsome.
anyways my bars looked much better than those.
personally, i think it’s fucked up how jake brings kyle buisness, and his bars come out this bad.
bump. still waiting for anything in reply by kyle to his defense.
Don’t hold your breath.
The only thing he could possible say to this is to offer a refund. It seems pretty obvious he’s not going to do that. So he’s going to just run from this like a not-so-mature 16 year old, and go try to scam elsewhere.
I say good riddance, but I feel bad for the next victim…
well let’s do what we can.
everyone who’s still subscribed and reading this, feel free to link to the photos i put up. post it in every forum you know. let everyone know what a punkass little scammer bitch kyle is.
i call rocket’s board, as well as the welding and fabrication forum. honda-tech too.
lots of car forums out there. let’s spread the word like wildfire and run this punk out of business before he’s even in business.
Kyle Curley
Curley Custom Fabrications
jake, it’s up to you if you want address/phone number posted.
and here’s the final pic for jake to post measurements of.
Ouch, I think all that was needed was the straight line going down the centre cutting the bar in half…you can tell just from that line that nothing is even close to matching up, but just getting $50 back is highly unreasonable, for a bar that can’t even go in your car, having slag everywhere, and the powdercoat being shit. And if you were the most mature 16 year old on the planet, you would realize you must give Jake back his money in return for the bar, and maybe you’ll learn a lesson on how to take your time building products that your going to sell to other people. Sorry Jake for taking a loss, but maybe in the end you’ll get your money back
ROFL… I’m sorry that I laughed…but… but…
that does look like it had been fabricated by a 16 year old.
Kyle had better cough up the $$$.
and the measurements… (wait til you hear what he says in response to this omfg roflmao)
orange-R:1/4"
L:5/16"
red-R:15/16"
L:1 3/8"
white-R:15 5/8"
L:14 1/2"
gray-R:8 13/16"
L:9"
purple-R:7 5/8"
L:7 15/16"
pink-R:8 11/16"
L:8 3/8"
yellow-R:9 5/8"
L:9 1/2"
blue-R:9 3/8"
L:9 9/16"
green-top:9"
bottom:9 15/16"
thats it guys… kyle officially has the littlest dick on the face of the planet.
red teggie… not only does it appear to be fabricated by a 16 year old… but it appears to be fabricated by Ray Charles, at 16 years old… :tsk: :argh:
so i confront him with this picture and the measurements and how does he respond? ill post the convo next but before i do let me say that i CAN use a tape measure, very well in fact. i am pulling a 4.0 in mechanical engineering and im very good at both math and measurements… (as if i had to tell any of you this, i mean fuck 4DOORTEG can tell from the line i drew down the center)…
blueoval557: got the money order…its going out tomorrow
IcemansZ28: so what did you buy with my money?
blueoval557: nothing yet
IcemansZ28: so r u gonna gonna send me the rest of it
IcemansZ28: or what
blueoval557: im sending you the $50…end of story
IcemansZ28: the bar isnt straight dude
IcemansZ28: there isnt one measurement consistent side to side
IcemansZ28: connect to me
<so i show him the pic right… and give him the measurements>
IcemansZ28: take a look at that
IcemansZ28: do you feel that that kind of misalignment is what i contracted you to build me?
IcemansZ28: are you proud of the bar you made me?
blueoval557: lmao…as i told you a million times before…THE THICKNESS OF A WELD BEAD VARIES! THERE IS ABSOLUTLEY POSITIVELY NO WAY YOU CAN GET ACCURATE MEASUREMENTS OF A PIECE AFTER A WELD BEAD IS AROUND IT. I WOULD SAY THE TOLERANCES ARE TO THE 1/4 INCH AT THE ABSOLUTE POSITVE MOST…ID BE SURPRISED IF THEY WERE THAT FAR OFF!
IcemansZ28: i measured very accurately
IcemansZ28: why would i lie about this
IcemansZ28: you seem really defensive
IcemansZ28: now are you proud of what you made me?
IcemansZ28: do you feel that thats what i asked you to build me?
IcemansZ28: answer these, for real
IcemansZ28: if you arent gonna pay me, at least answer my questions
blueoval557: yes i am proud of what i built you…as i said, their is no way an accurate measurement can be taken after a weld bead is in the picture…NO WAY! end of story. i have a feeling you will ask if i would put it in my car so lemme get it outa the way right now…
IcemansZ28: are you even the least bit sorry that it totally fuckin sucks
blueoval557: no it would not go into my car…not because of the fabrication aspect of it…but because of the design
IcemansZ28: i am sure u bolted it in your car
blueoval557: duyde, how many times do i have to tell you everything! thats why i may seem defensive…i am soo tired of the same questions over n over n over…
blueoval557: THE DAMN THING WAS COMPLETELY WELDED WHILE BOLTED INTO MY CAR!
IcemansZ28: kyle dude… you are gonna regret fucking me over one day, this isnt a threat
IcemansZ28: im just sayin
IcemansZ28: karma is gonna get you bad dude
IcemansZ28: isnt that cool how everyone on g2ic, even your friends are on my side?
blueoval557: do i believe in that whole “karma” thing…absolutely…did i screw you over…not in my opinion no
IcemansZ28: are you proud of what you made me?
IcemansZ28: like would you put it on your business website if you had one?
blueoval557: isnt that cool…how i dont really have “friends” on g2ic…i would consider MAYBE 5 ppl off of the entire site my “friends” bc most r stupid lil asshats but thats jus my opinion…it used to be soooo much better about a yr or so ago
blueoval557: defenitely…to tell you the truth, the reason i dont have my site together is because i was waiting for a pic of the bar installed in your car so i could have a “gallery” section on my site…n no i am not lyin…honest to god truth
IcemansZ28: if you want ill put the pieces in separately so i can take pics of them one at a time
IcemansZ28: as ive told you
IcemansZ28: they will not bolt together
IcemansZ28: this is what a $420 product looks like…
IcemansZ28: http://www.honda-tech.com/zerothread?id=879799
IcemansZ28: show your mother that
IcemansZ28: then show her the pics of my bar on the site
IcemansZ28: see what she thinks
IcemansZ28: look at THOSE welds…
IcemansZ28: and yes i know they are tig
blueoval557: hell, if you wanted me to tig, i defenitely could of done it. BUT…u think $420 is expensive??? hahahaha did u ever see the picture of the tig weld on stainless steel i did? if not, IM later today and ill send it to you, then try to tell me i cant weld…
HOLY SHIT THIS MEANS HE COULD HAVE TAKEN ME FOR EVEN MORE MONEY. even if the welds were pretty its still off like the leaning tower of Pisa. :mad:
blueoval557: lmao…as i told you a million times before…THE THICKNESS OF A WELD BEAD VARIES! THERE IS ABSOLUTLEY POSITIVELY NO WAY YOU CAN GET ACCURATE MEASUREMENTS OF A PIECE AFTER A WELD BEAD IS AROUND IT. I WOULD SAY THE TOLERANCES ARE TO THE 1/4 INCH AT THE ABSOLUTE POSITVE MOST…ID BE SURPRISED IF THEY WERE THAT FAR OFF!
so what is he trying to tell me, that i cant use a tape measure? what kind of blatant disregard for factual proof is this? i measured from where the bars would be, very precisely, using tape, a straight edge. im an artist, an engineer (in the works), and a perfectionist. kyle is none of these things. kyle is a high school kid who has never even had a semester of calculus or physics in his life. so what do you think g2ic, did i really just pull these measurements out of my ass? come on. as if its not fucked up enough already, i gotta go make shit up. jesus tapdancing christ…
anyone else wonder why kyle has suddenly disappeared from the thread. I DARE YOU TO RESPOND YOU ASSCLOWN… or are u scared? :uhoh:
Just take him and/or his mom to court. 
omg did he harness the power of the sun for these welds??? All i gotta say is NICE
It really looks like this was his first time welding, when I was learning how to braze weld when I was 14 even they looked better then his shitty welds :gay:
blueoval557: isnt that cool…how i dont really have “friends” on g2ic…i would consider MAYBE 5 ppl off of the entire site my “friends” bc most r stupid lil asshats but thats jus my opinion…it used to be soooo much better about a yr or so ago
that’s right kyle…you weren’t here ripping people off a year ago.
jake…seriously–sue his mother. if he is gonna start acting like a little whiny bitch everytime something doesn’t go his way (see also: dustin curley), take his bitchass to court.
according to neil, as of last night kyle’s last login to g2ic was monday around 7.
Mark speaks the truth. Sue the bitch
another G2IC member pointed this out to me. I thought it was interesting.
blueoval557: no it would not go into my car…not because of the fabrication aspect of it…but because of the design
but yet…
blueoval557: THE DAMN THING WAS COMPLETELY WELDED WHILE BOLTED INTO MY CAR!
sounds like the usual curley family bullshit that’s fed out whenever a curley family member is caught in a lie that’s gonna end up with a punkass bitch getting served. hardcore.
ouch